New Holland Discbine 316 / NOT AVAILABLE
Features
CLOSER CUTTING, FASTER DRYDOWN, INCREASED DURABILITY
New Holland has taken the Discbine® mower-conditioner to a new level with two new center-pivot models. Combining both speed and performance, the new Discbine® 313 and Discbine® 316 feature increased durability, more efficient crop flow and smoother, more effective conditioning.
LARGER DISCS, WIDER CONDITIONING
The combination of larger cutting discs and a wider conditioning system leads to cleaner cutting, better crop flow and more consistent drying. Co-rotating disc modules have been removed on the Discbine 313 and reduced to one pair on the Discbine 316. This greatly reduces the crop convergence between the cutterbar and the conditioner.
IMPROVED FLOTATION
Improved header attaching link geometry contributes to more responsive flotation. The rear pivot points of the header attaching links are lower than the pivot points on the front, ensuring the header moves up and back should you encounter an obstacle. In addition, the upper end of the flotation springs are anchored with a ball-and-socket arrangement that eliminates any binding as the header moves through its flotation range.
Specifications
|
Model |
Discbine 316 |
|
Cutting width ft. in. (m) |
16' 3" (4.95) |
|
Cutting height in. (mm) |
0.79 - 2.7 (20 - 69) |
|
Cutting height w/opt. high-stubble shoes in. (mm) |
3.1-5.5 (79-140) |
|
Cutting height w/opt. Biomass shoes in. (mm) |
4.9-7.8 (124-198) |
|
Cutting height w/opt. adjustable shoes in. (mm) |
0.79-5.8 (20-147) |
|
Cutterbar tilt angle degrees |
2 - 10 |
|
Type cutterbar |
Modular |
|
Number of discs/knives per disc |
10/2 |
|
Disc speed @ 1000 rpm PTO speed rpm |
2250 |
|
Knife tip speed @ 1000 rpm PTO speed mph (k/h) |
162 (261) |
|
Cutterbar flotation |
Vertical and lateral, adjustable springs |
|
Cutterbar drive method |
PTO drive w/slip clutch to bevel gearbox at LH end of header, vertical PTO shaft to cutterbar |
| Conditioner | |
|
Type |
Chevron intermeshing molded rubber, or chevron intermeshing steel rolls |
|
Length in. (mm) |
125 (3175) |
|
Diameter in. (mm) |
2 x 10.4 (264) rolls |
|
Conditioner drive method |
4 HB v-belt & enclosed gears |
|
Speed rpm |
750 or 640 |
|
Conditioning roll tension adjustment |
Single crank |
|
Conditioner gap adjustment |
Drawbolt stop, each end |
|
Swath width ft. (m) |
10 (3.0) |
|
Windrow width ft. (m) |
3 - 8 (.9 - 2.4) |
| Driveline | |
|
Input speed rpm |
1000 |
|
Driveline protection |
Slip clutch and overrunning clutch assembly @ rear of PTO shaft |
| Tractor Requirements | |
|
Minimum PTO power required hp (kW) |
100 (75) |
|
PTO shaft spline/size requirements |
21-spline/1 3/8" |
|
Hydraulic circuits required |
2 |
|
Minimum relief pressure required, psi (bar) |
1500 (103) |
|
Electrical |
7-pin electrical connector for transport lights |
|
Drawbar/3-pt Hitch |
ASAE Cat. III drawbar or Cat. III 3-pt hitch |
| Tires | |
|
Tubless Ag rib implement tires |
12.5L x 15 8PR |
| Transport Speed, Maximum | |
|
Transport Speed, Maximum mph |
20 (32) |
| Dimensions ¹ and Weight ² | |
|
Width, transport ft. in. (m) |
16' 7" (5.05) |
|
Width, operating ft. in. (m) |
25' 7"(7.8) w/2-pt swivel hitch; 23' 11" (7.3) w/drawbar swivel hitch |
|
Length, transport ft. in. (m) |
32' 0" (9.7) w/2-pt swivel hitch; 31'' 0" (9.4) w/drawbar swivel hitch |
|
Length, operating ft. in. (m) |
26' 7" (8.1) w/2-pt swivel hitch; 25' 7" (7.8) w/drawbar swivel hitch |
|
Height, transport ft. in. (m) |
7' 5" (2.26) |
|
Height, operating ft. in. (m) |
6' 7" (2.01) |
|
Ground clearance w/header fully raised in. (mm) |
16.2 (411) |
|
Weight, Shipping lb. (kg) |
Less Hitch 6845 (3104); w/2pt or dbr 7020 (3184) |
|
Weight, Operating lb. (kg) |
w/2pt or dbr 6700 (3039) |
